TS Series 4 Axis 9.0Nm 1274.5oz.in Nema 34 Closed Loop Stepper Kit with Power Supply

$948.46

Nema 34 Closed Loop Stepper Kit.

Out of stock

TS Series 4 Axis 9.0Nm (1274.5oz.in) Nema 34 Closed Loop Stepper Kit w/ Power Supply

This CNC kit includes the following:

  • 4 x Nema 34 Closed Loop Stepper Motor 9.0Nm/1274.5oz.in with Encoder 1000PPR
  • 4 x Closed Loop Stepper DriverV4.1 0~8.2A 24~80VDC for Nema 34 Stepper Motor
  • 4 x 350W 60V 5.9A 115/230V Switching Power Supply Stepper Motor CNC Router Kits
  • 4 x 1.7 m(67″) Long Encoder Extension Cable for Closed Loop Stepper Driver
  • 4 x AWG18 1.7 m(67″) Long Motor Extension Cable with GX16 Aviation Plug
  • 1 x RS232 Debugging Cable

Motor Specifications

  • Manufacturer Part Number: 34HS46-6004D-E1000
  • Number of phases: 2
  • Step Angle: 1.8 deg
  • Holding Torque: 9.0 Nm(1274.5oz.in)
  • Rated Current/phase: 6.0 A
  • Phase Resistance: 0.62 ohms± 10%
  • Inductance: 6.3 mH ± 20%(1KHz)
  • Frame Size: 86 x 86 mm
  • Body Length: 117 mm
  • Shaft Diameter: Φ14 mm
  • Shaft Length: 37 mm
  • Keyway Shaft Length: 25 mm
  • Lead Length: 300 mm

Encoder Specifications

  • Output Circuit Type: Differential type
  • Encoder Resolution: 1000PPR
  • Output Signal Channels: 3 channels
  • Supply Voltage Min: 4.5V
  • Supply Voltage Max: 5.5V
  • Output Current: 100mA MAX
  • Output High Voltage: ≥Vcc-0.4V
  • Output Low Voltage: ≤0.4V
  • Output Frequency Max: 1.85MHZ

Encoder Specifications

white
red
blue
black
green
yellow
GND
+5VCC
EA-
EA+
EB-
EB+

Driver Specifications

  • Output Peak Current: 0~8.2A
  • Input Voltage: +24~80VDC (Typical 48VDC)
  • Logic Signal Current: 7~16mA (Typical 10mA)
  • Pulse Input Frequency: 0~200kHz
  • Quick response, no delay, and almost no settlement time
  • High torque at starting and low speed, high stiffness at standstill
  • Offer servo-like performance at a much lower cost

Power Supply Specifications

  • 60V DC 5.9A output
  • AC input voltage range: 93~132V/176~264VAC
  • 115V/230V AC selected by switch
  • High-efficiency low cost
  • Forced air cooling by built-in DC fan
  • Low output ripple and yawp
  • Over-current, over-voltage, short circuit, and overheat protections
  • 215*115*50mm (L*W*H)

Motor and Encoder Connection

PIN
1
2
3
4
Motor
A+
A-
B+
B-
PIN
2
3
1
13
11
12
Encoder
VCC
EGND
EA+
EA-
EB+
EB-

Motor Extension Cable Connection

PIN
1
2
3
4
Color
White
Green
Blue
Black

OR

PIN
1
2
3
4
Color
Black
Green
Red
Blue

Encoder Extension Cable Connection

PIN
2
3
1
13
11
12
Color
Red
White
Black
Blue
Yellow
Green
PLEASE NOTE: The thick black wire can be used for shielding but is not required, so you can leave it unconnected.
More From: